 |
| Home | Contact |
Stearalkonium Chloride or Benzyldimethyl(octadecyl)ammonium Chloride Supplier SDS Safety Data Sheet of Exporter Manufacturers' Representative |
| Email: info@ammol.org |
| Call Toll Free +1-855-552-6665 Toll Free: 1-855-55-AMMOL |
Stearalkonium Chloride
CAS Number: 122-19-0
Molecular Formula: C27H50ClN
Molecular Weight: 424.15
Stearalkonium Chloride
Stearalkonium Chloride or Benzyldimethyl(octadecyl)ammonium Chloride
SDS, Safety Data Sheet
MSDS Sheet, Material Safety Data Sheet 17-August-26
1. PRODUCT DESCRIPTION
Product Name & Other Names: Stearalkonium Chloride or Benzyldimethyl(octadecyl)ammonium Chloride.
CAS Number: 122-19-0
EINECS EC Number: 204-527-9
HS Code: 29239000
Molecular Formula: C27H50ClN
Molecular Weight: 424.15
Relevant uses and uses advised against (if any): Industrial Manufacturing.
Supplier: American Molecules, 9910 Bent Oak Dr, Houston, TX 77040, USA.
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665.
In case of emergency contact: Will be given with the supply.
2. HAZARD IDENTIFICATION
GHS, Globally Harmonized System Classification in accordance with 29 CFR 1910
Classification according to Regulation (EC) No 1272/2008
Not a hazardous substance or mixture according to Regulation (EC) No. 1272/2008.
This substance is not classified as dangerous according to Directive 67/548/EEC.
Labeling according to GHS & Regulation (EC) No 1272/2008
| GHS Label Elements None |
Signal Words: None
Precautionary statements:
P261: Avoid breathing dust/fume/gas/mist/vapors/spray.
P262: Do not get in eyes, on skin, or on clothing.
P281: Use personal protective equipment as required.
P302+P352: IF ON SKIN: Wash with plenty of soap and water.
P304+340: IF INHALED: Remove victim to fresh air and keep at rest in a comfortable position for breathing.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P337+313: If eye irritation persists get medical advice/attention.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Product Name & Other Names: Stearalkonium Chloride or Benzyldimethyl(octadecyl)ammonium Chloride.
CAS Number: 122-19-0
EINECS EC Number: 204-527-9
4. FIRST AID MEASURES
Always get medical attention after the first aid is over.
Emergency and First Aid Procedures:
Eyes - Flush with water for at least 15 minutes, raising and lowering eyelids occasionally. Get medical attention if irritation persists.
Skin - Thoroughly wash exposed area for at least 15 minutes. Remove contaminated clothing. Launder contaminated clothing before reuse. Get medical attention if irritation persists.
Ingestion - If swallowed, if conscious, give plenty of water. Immediately call a physician.
Inhalation - Remove to fresh air. Give oxygen if breathing is difficult; give artificial respiration if breathing has stopped. Keep a person warm, quiet, and get medical attention.
5. FIREFIGHTING PROCEDURES
Extinguisher Media: Use water spray, alcohol-resistant foam, dry chemicals, or carbon dioxide. Avoid solid water jet as it can spread the fire.
Special Fire fighting Procedures: Firefighters should wear full protective equipment and NIOSH approved self-contained breathing apparatus.
Unusual Fire and Explosion Hazards: Heated to decomposition, however, toxic chemicals, chlorine compounds, oxides of nitrogen and oxides of carbon along with fumes may be evolved.
Special Information: In the event of a fire, wear full protective clothing and NIOSH-approved self-contained breathing apparatus with full face piece operated in the pressure demand or other positive pressure mode. At high temperatures under fire conditions, it may produce toxic or irritating fumes.
6. SPILL OR LEAK PROCEDURES
Personal precautions, protective equipment, and emergency procedures: Ventilate area of spill. Avoid creating dust. Avoid breathing dust/fumes/gas/mist/vapors/spray. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Environmental precautions: Do not let the product enter drains, soil, or water sources.
Methods and materials used for containment, cleanup procedures and Storage: Contain spilled material. Cover with an inert, non-combustible absorbent material, (e.g., sand, earth, diatomaceous earth, vermiculite). Vacuum or sweep-up and remove it into an approved disposal container.
7. SPECIAL PRECAUTIONS
Precautions for safe handling: Apply according to good manufacturing and industrial hygiene practices. Ensure proper ventilation. Wash thoroughly after handling it. Do not drink, eat, or smoke while handling. Provide appropriate exhaust ventilation at places where dust is formed. Avoid contact with skin, eyes, and clothing. Minimize dust generation. Avoid breathing dust/fumes/gas/mist/vapors/spray. Keep container tightly closed. Avoid ingestion and inhalation. Use individual protective equipment (waterproof boots, suitable protective clothing, safety glasses, etc.).
Conditions for safe storage, including any incompatibilities: Store in cool, dry, and ventilated area away from heat sources and protected from sunlight in tightly closed original containers. Keep air contact to a minimum. Do not leave the material container open. Store protected from heat, sparks and ignition sources and incompatible materials. Avoid contact with skin and eyes. Avoid inhalation of dust/mist/vapor. Do not store with incompatible materials like Strong oxidizing agents. Storage: Store at room temperature in a cool, dry place, away from heat or direct sunlight.
8. SPECIAL PROTECTION INFORMATION
Exposure limits: Not established.
Respiratory Protection (Specify Type): None needed under normal conditions of use with adequate ventilation. NIOSH approved equipment should be worn if PELs are exceeded.
Ventilation System: A system of local and/or general exhaust is recommended to keep employee exposures as low as possible.
Personal Respirators (NIOSH Approved): For conditions of use where exposure to dust or mist is apparent and engineering controls are not feasible, a particulate respirator may be worn.
Skin Protection: Wear protective gloves and clean body-covering clothing.
Eye Protection: Use chemical safety goggles and/or full-face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Other Control Measures: Maintain good housekeeping in work area. Handle in accordance with good industrial hygiene and safety practice.
9. PHYSICAL DATA
Physical State: White to yellow solids.
Odor: No data found.
Odor threshold: No data found.
pH: about 4 to 6.
Relative density: No data found.
Melting Point: 54C to 56C literature.
Initial boiling point and boiling range: No data found.
Flash point: No data found.
Auto-ignition temperature: No data found.
Decomposition temperature: No data found.
Upper/lower flammability or explosive limits: No data found.
Vapor pressure: No data found.
Vapor density: No data found.
Evaporation rate: No data found.
Flammability (solid, gas): No data found.
Partition coefficient: n-octanol/water: No data found.
Solubility in Water: No data found.
Viscosity: No data found.
10. REACTIVITY DATA
Stability: Stable under recommended condition of storage.
Conditions to Avoid: Dust generation, Incompatibles
Incompatibility (Materials to Avoid): Strong oxidizing agents.
Hazardous Decomposition Products: Toxic chemicals, chlorine compounds, nitrogen, and carbon along with fumes.
Hazardous Polymerization: Will not occur.
11. TOXICITY DATA
Toxicity Data: No data found.
Carcinogenicity: Not listed as carcinogen by IARC, ACGIH, OSHA and NTP.
Mutagenic Effects: No data found.
Developmental Toxicity: No data found.
Reproductive Effects: No data found.
12. ECOLOGICAL DATA
Toxicity to fish, daphnia, and other aquatic invertebrates: No data available.
Persistence and Degradability: No data found.
Mobility: No data found.
Results of PBT and vPvB assessment: No data found.
13. DISPOSAL INFORMATION
Waste Disposal Methods: Dispose in accordance with all applicable regulations.
14. TRANSPORT INFORMATION
DOT (USA) & ADT/RID Europe: Not controlled.
IMDG & IATA: Not controlled.
15. REGULATORY INFORMATION
USA Regulations:
SARA 311/312 Hazard Categories: See section 2.
16. ADDITIONAL INFORMATION
Disclaimer:
**************************
Our company provides this MSDS sheet in good faith but makes no representation as to its comprehensiveness or accuracy. This SDS sheet is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. The above information has been compiled from various sources and has the possibility of discrepancy and being out-dated information. Individuals receiving the information must exercise their independent judgment and do further search in determining its appropriateness for a particular purpose. In no case shall our company be liable to loss or damages by the product user.
**************************
Please visit Main Page of Stearalkonium Chloride Suppliers.
American Molecules, also known as ammol.org is a distributor, supplier and manufacturers' representative of all types of Pharmaceuticals, Functional Ingredients, Excipients and Specialty Chemicals in Texas USA. Our principals manufacture supply and export USP NF BP, Ph Eur, etc grades of chemicals pure and reagent grade, mineral fortifiers, FCC food grade. Tailor made particle size and customized specifications are offered. The principal's facility is having one or more of the certifications like FDA approval and GLP, cGMP, ISO9001, ISO14001, ISO/IEC 17025, ISO22000, FSSC 22000, ISO45001, FSSAI, Kosher, HALAL, COPP, WHO-GMP certified and Written Confirmation (WC) for export to Europe is available. The manufacturers suppliers and exporters observe WHO Good Manufacturing Practices and Good Laboratory Practices.
Suppliers and Manufacturers' Representative:
9910 Bent Oak Dr
Houston, TX 77040, USA
Call Toll Free: 1-855-55-AMMOL 1-855-552-6665
Email: info@ammol.org